Others also read
| For the past five years, Nile Aluminium & Metals Company, or AluNile, has had very positive experiences with Glaston's first FC500™ tempering furnace sold outside Finland.
| Being highly focused on flat glass processes for partitioning used in the office industry, Tufwell Glass Ltd has carved out a unique and resilient position for itself in southeast region of England.
| Spandrel glazing has developed to a stage where more efficient insulation can generate higher thermal stresses than can normally be resisted by heat strengthened (HS) glass on which ceramic enamel (frit) has been applied.
| After 10 years of experience with the Glaston HTF 2142 furnace, Paul Buckley, Managing Director of the PJB Glass Group, decided to complement his flat glass production offering by investing in a Glaston RC200™ furnace.
| The Flachglas Group employs around 1,100 employees at three sites in Switzerland and three sites in Germany – around 650 of them generate revenues of approx. € 70 million at the Wernberg site (Bavaria).
| Sanshiba Shozai of Japan chose to be the first glass processor in the world to invest in Glaston’s latest GlastonInsight™,the intelligent online assistance system, at the same time as it ordered the Glaston RC350™ tempering furnace.
| Thanks to on-going research and development efforts glass products can take on ever new functions.
| Finding ways to improve energy efficiency is one of the greatest challenges facing contemporary architecture.
| Frank Lloyd Wright's reasoning for the building design was that he wanted the Kaufmann family to live with the waterfalls, to make them part of their everyday life, and not just to look at them now and then.
| In the last few years, the production of insulating glazing units (IGU) evolved to develop composi-tions to obtain high thermal insulation performance: double glazing filled with Argon/Kripton gas, low-emission glazing, warm-edge spacers and triple glazing.
| A report has been commissioned by Thermoseal Group and produced by an independent warm edge consultant that shows a comparison of the thermal performance through the edge of insulated glass, including: Warm Edge Spacer Bar, Desiccant, PIB and Sealant.
| Contact angle measurements using method based on B-spline snakes (active contours) were applied to investigate surface wettability properties of commercial soda-lime-silica float glass subjected to various surface preparation methods.
| Breakage patterns, residual stress, and fractured surfaces on tempered glasses are investigated to find the correlation among glass thickness, tempered level, and the number of fragments, particularly when the glass thickness is less than 4 mm.
| An Introduction to Design and Performance by Dr. Cenk Kocer - University of Sydney, School of Physics, Sydney 2006
| Everyone in Germany knows the expression “yellow angel”, and most of its 17 million members have already made use of the organization's road assistance service at least once: it is the largest automobile club in Europe, the ADAC.
| Insulating glass desiccants with different components give quiet disparate quality performances.
| In the façade industry, glass panes have been bonded to aluminium frames with UV-resistant silicone adhesives for 40 years with almost unchanged mechanical strength.
| The paper shows that the residual stress at the surface of tempered glass panels may vary both locally and globally, i.e., stresses near the edges and corners of the panels may be considerably different from the stresses in the middle part of the panels.
| The new Spiegel headquarters and the neighbouring office complex, the Ericus-Contor, a fourteen and nine-storey building pair, expand the gallery of internationally recognized architectural works in Hamburg.
| The canopies are a composite construction between both steel and glass, leaving no element without stress or structural function.
| Glass industry standards in different countries require 24/7 quality control with the same specifications and fully automated analyses and following statistics.
| Despite increasingly demanding requirements to save energy and a focus on reducing our use of prime energy, we also need to bear in mind economics and cost effectiveness during the construction phase of buildings, especially on larger projects.
| glassonweb.com dedicates the weekly focus to a technical article titled "A Sealed System for Heatable Glass - A New Product; the article is written by Prem Boaz, President of Glass Products Consulting LLC in Port Orange, Fla..
| At this year's GPD in Finland LiSEC was represented by two lecturers.
| Firstly, it would be great if everyone in the glass industry refrained from calling this product “bullet proof” I seriously doubt if anything is ultimately bullet proof, bullet resistant is indeed the correct terminology and within the industry this is abbreviated to BRG.